Home > Pre-War Parts Department > Springfield New Phantom
Choose a model:
Engine
Sort By:
1 2
Wheel Removal Video, Springfield AD4 Fuse Panel Terminal AD5 Master Switch Terminal with open end
This video demonstrates how to use the wheel wrench to remove the wheel nut and wheel. AD4 Terminal closed end for fuse panel Terminal for master switch open end
AGP1E20- Auto-Vac Gaskets SP1points- Ignition Points for DeJon Distributors A2347P Wheel Wrench Instruction Plate
Auto-Vac gasket set for Late Silver Ghost, Early British Phantom 1 up to Chassis 1 EF, and 20hp. Set includes two top cover assembly gaskets, Fuel filter gasket, and drain plug gasket. Gaskets are made from composite cork/neoprene and are suitable for modern fuels with or without ethanol. Points ignition contacts for SP1 w/DeJon distributor. Sold in pairs only Instruction plate for buffalo type wheel wrench used on Springfield cars
SP1airfilter- Air Filter Element F80727 Rubber pad set for screw that attaches firewall to scuttle A9981 Optima 6v Battery Holdown
Air cleaner element for Springfield PI only. This is a modern replacement for the original element and a direct fit. Rubber pad set for screw that attaches firewall to scuttle Battery hold down for Optima 6 volt
E74889 Rubber Coupling Drive Disc AF2- Panel Screw AW Assort- Aluminum Washer Assortment
Rubber Coupling Disc for dynamo drive and magneto drive Bolt battery box cover and valence panels above running boards usually found on Springfield Silver Ghost and Springfield Phantom I. Reproduced in stainless steel. Priced per each. Aluminum Washers are great for sealing connections involving fuel, oil, and coolant. Included are the most common sizes found on most Rolls-Royce and Bentley motorcars. The sizes and quantities are listed in the extended information tab.
E22599 Tail Pipe Bracket E71184 E70647 bracket for carburetor induction hot spot chamber
E71184
: $86.00
Bracket for exhaust tail pipe. Reproduced in heavy gauge stainless steel. Bracket for ignition wire loom includes E 73760 for aluminum head engines only P1, SP1 Bracket hot spot iron head Phantom I only sold in pairs
A10358 cover for generator cut-out TRPAL Trilin Lens Right Amber Plastic TRPAR Trilin Lens Right Amber Plastic
Cover for generator cut-out mounted on generator of Springfield Phantom I with Rolls-Royce made generator Trilin Taillight lens reproduced in UV resistant plastic. This lens is Amber and is placed in the outside of a right mounted light. Trilin Taillight lens reproduced in UV resistant plastic. This lens is Amber and is placed in the outside of a Left mounted light.
TRPRED Trilin Lens Red Plastic 6v to 12v inverter U708 Dont Hammer Spanner
Trilin Taillight lens reproduced in UV resistant plastic. This lens is Red and is placed in the center bottom of the light. inverter- converts 6 volt positive ground to 12 volt negative ground. Great for providing a power source to charge cell phones, GPS, overdrives, and much more that requires 12 volts Wrench for Silver Ghost valve port caps, Springfield Phantom I engine oil drain plug and transmission oil filler plug. Reproduction
AF5 foot pedal pad A-9350 base for generator cut-out AF8070 Brush Set Starter
Pedal pad set Springfield Silver Ghost and Springfield Phantom I. Sold in pairs only Cover for generator cut-out mounted on generator of Springfield Phantom I with Rolls-Royce made generator Starter motor brush set for Springfield P1 six volt Rolls-Royce made unit
F74896- Shock Absorber Piston Link AD7 Headlight Connector AF4 Bijur Tank Cap
Connects shock absorber internal piston to the shock absorber arm. For Rolls-Royce manufactured hydraulic shocks only. Applies to front and rear Phantom 1 and early Phantom 2 rear shocks only. It is an assembly of F74566 and F74896. This is New Old Stock. Headlight and Cowl light connector for drum style lights. These are single contact for single beam headlight and cowl light bulbs. They are reproduced just as the originals. Connector set includes one socket and one plug. Double contact connectors also available ,part number AD6. Cap for Bijur tank. Reproduced in aluminum to replace the original zinc die-cast original that tends to fracture. Fits Springfield Phantom I early cars with threaded type cap only.
AD6 Headlight Connector A70353 Water Pump Shaft/Rotor SMC22 Rubber Bumper Mounts
Headlight and Cowl light connector for drum style lights. These are double contact for double filament high/low beam headlight bulbs. They are reproduced just as the originals.They can also be used in the cowl lights for fitting double filament bulbs for turn signals. Connector set includes one socket and one plug. Single contact connectors also available AD7. Water pump shaft and rotor assembly for Springfield Phantom 1. Shaft has been reproduced in stainless steel. Rubber bumper mounts for tubular bumpers front and rear. Sold in pairs. Reproduced exactly as original with offset center hole for leveling
   
 
1 2